PENGGUNAAN MOTOR WIPER UNTUK MESIN PENGANGKUT SAMPAH SELOKAN

Gunawan Toto Hadiyanto; Aji Saputra

doi:10.59562/metrik.v20i3.48070

PENGGUNAAN MOTOR WIPER UNTUK MESIN PENGANGKUT SAMPAH SELOKAN

Gunawan Toto Hadiyanto^(1*), Aji Saputra⁽²⁾,

(1) Universitas Batam
(2) Politeknik Caltex Riau
(*) Corresponding Author

DOI: https://doi.org/10.59562/metrik.v20i3.48070

Abstract

Floods that hit areas that are supposed to be areas where flooding is impossible are often caused by garbage stuck in the ditches. As one of the causes of flooding in big cities such as Batam, so it is necessary to installtion a machine to collect waste bottles and other waste in the ditches to remove the waste and bottles that are in the ditches. The utilisation of a DC motor driven machine used in cars as a wiper drive can be used and controlled to drive a garbage collector which is relatively not too heavy on the load. DC motor rotation is forwarded to the engine drive wheel using a chain. The system for lifting garbage from the gutter to the storage tanks uses a chain that has been modified into a conveyor. The use of a conveyor slot which can be adjusted from 30cm to 60 cm wide by manually shifting the wheel base is necessary to overcome the width of the gutter which sometimes varies in width. The Motor DC result shall capable of moving forward or reverse, so the machine should move forward or backward the ditch with a speed of 0.0704 – 0.0759 m/s with a success rate of lifting 75.94% waste and is capable of transporting a maximum of 3 rotational waste bottles.

Keywords

Motor Wiper,Motor DC, Garbage transporter

Full Text:

PDF

References

S. M, A. Haslinah, S. Ma’ruf, and H. Gunawan, “Rancang Bangun Prototype Alat Pengangkut Sampah Otomatis Pada Saluran Air,” ILTEK J. Teknol., vol. 17, no. 01, pp. 32–36, 2022, doi: 10.47398/iltek.v17i01.66.

D. A. Suheri, D. N. Ditya, K. Sandi, and L. R. Sari, “Rancangan Alat Pengangkut Sampah Tenaga Angin (PESTA) Sebagai Upaya Pengurangan Sampah Perairan,” J. Teknol. dan Ris. Terap., vol. 1, no. 2, pp. 43–47, 2019, doi: 10.30871/jatra.v1i2.1422.

A. Indra Komara and L. Fattah Buchari, “Perancangan Alat Pengangkut Sampah Pada Saluran Air Secara Kontinyu,” J. Teknol. dan Rekayasa Manufaktur, vol. 1, no. 2, pp. 73–86, 2019, doi: 10.48182/jtrm.v1i2.10.

A. Y. Pratama, Y. Rahma, and A. Normassari, “Jasa Pengangkut Sampah ( Sangkuts) Berbasis Android Di Kabupaten Kudus,” Simetris J. Tek. Mesin, Elektro dan Ilmu Komput., vol. 9, no. 1, pp. 35–40, 2018, doi: 10.24176/simet.v9i1.1656.

G. Hadiyanto, “P Pemanfaatan Arduino Uno sebagai Alat Ukur Offset Voltage pada Infra Red Detector type TO39 dengan pembanding alat ukur DMM,” Elkom J. Elektron. dan Komput., vol. 14, no. 1, pp. 121–129, 2021, doi: 10.51903/elkom.v14i1.331.

R. Alfian and A. Phelia, “Evaluasi Efektifitas Sistem Pengangkutan Dan Pengelolaan Sampah Di Tpa Sarimukti Kota Bandung,” JICE (Journal Infrastructural Civ. Eng., vol. 2, no. 01, p. 16, 2021, doi: 10.33365/jice.v2i01.1084.

M. R. W. Kusuma, E. Apriaskar, and D. Djunaidi, “Rancang Bangun Sistem Pembersih Otomatis Pada Solar Panel Menggunakan Wiper Berbasis Mikrokontroler,” Techné J. Ilm. Elektrotek., vol. 19, no. 01, pp. 23–32, 2020, doi: 10.31358/techne.v19i01.220.

N. Nugroho and S. Agustina, “Analisa Motor Dc ( Direct Current ) Sebagai Penggerak Mobil Listrik,” Mikrotiga, vol. 2, no. 1, pp. 28–34, 2015.

Hathaway, Richard B., “Mechanical Engineering Vehicle Design”. Western Michigan University: Lecture Notes.,2000.